How to make a Skater Skirt

Two posts in a week!!  I think it is about time I did some catching up!  :D  Here are the instructions to make the pattern for a skater skirt, using the tailored skirt block from the previous tutorial.  This pattern will give you a 12 panelled skirt.

Skater Skirt

Step 1

Trace off the skirt block as one piece.  Move the side seam to the centre of the block.  Divide the block along the hip line into 6 equal parts and draw lines from the top to the bottom of the block to make the panels.  Make sure these are at right angles to the hip and hem line.  The red lines in the drawing are the original block lines, the blue ones are the new lines for the pattern.

Step 1

Step 2

Draw a dotted line parallel to the waist and hip line, 14cm down from the waistline.  Construct new darts on the panel lines to touch this line.  Ignore the old darts (the ones in red on this drawing).  The darts on the back panel lines are 2.5cm each, and the front darts are 1.5cm each.  Add 1cm to the back and front side seams and draw a new curved line to the hip point.

Step 2

Step 3

Decide where the skirt will sit at the waist, whether you are having a straight waistband, a shaped waistband or a facing.  Also decide on the finished length.  For this project I dropped the waist line by 2cm and made the skirt 40cm long overall.  Mark the length – don’t worry to add a hem allowance at this point, it is better to have the finished length when you toile it up.  Adjust the waistline accordingly.

Step 3

Step 4

Cut along the new waistline.  Number the panels and add grainlines perpendicular to the hipline on each panel.  Cut off the bottom at the new hemline.

Step 4

Step 5

Mark a facing 5cm deep on the pattern and trace this off, including the markings for the darts.  Cut the facing and close the darts to make a curved pattern shape.  Mark the centre front and back, and for a skirt with a side zip, label the centre lines as being placed on a fold.  You will need to add a seam allowance to the side seam of each facing piece, as well as to the top.  Standard seam allowance is 1.5cm.

Step 5

 Step 6

Cut up the panel lines of the skirt.  Stick paper down each side of the panels and add 3-5cm (or more if you want a really full skirt) to each side of each panel piece.  Add seam allowance to the top and sides of each panel, but leave the hem for now.  The pieces I show have had the fulness added from the dotted line that was 14 cm down from the waistline.  You could also use the hipline as the start point.  This would make the skirt more fitting to the hip, only flaring from there.  You need to decide where you would like the fullness to start.  I have shown a 4cm flare at the hemline.

Step 6

So that is your pattern.  For making up, it is easier to make the whole front and back, and then to attach them at the side seams.  Remember to leave the left side seam open to the hipline for a zip.  Sew the front and back facing together at the right side seam.  Attach the facing to the top edge of the skirt, clip and understitch.  Interface the facing.  At the toile stage you can finalise the finished length, then add the hem allowance to the paper pattern.  For this skirt 2cm should be sufficient.  The fuller the skirt the more difficult it will be to hem with a deep allowance.

I would love to see the skirts made using this tutorial, so please post them, either on Burdastyle or Pinterest, with a link back here.  Happy pattern cutting!

About these ads

One thought on “How to make a Skater Skirt

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s